Currently on the market there are many families of water purifiers in which people often refer to RO reverse osmosis water filters . So which mechanism helps RO water purifier filter all kinds of water from wells, tap water, rainwater, even salty water to drink directly without having to boil ? AXIOS REVIEW will help you to answer the most specific and easy to understand principles of the whole house water purifier installation as well as the detailed diagram through the article below!
Principle of whole house RO water purifier installation
For a RO water purifier to filter out pure drinking water directly without having to boil it, the structure of the filter system from components such as filter elements, RO membrane, pressure tank … must be ensured to reach the highest quality, especially the set of filters.
- There must be a minimum of 7 filters and operate sequentially according to the steps.
Specifically, the filtering steps are as follows:
Step 1: The filtered water will be passed through the 5 micron PP filter element, which will help to remove moss, dirt, sandy soil. Although this filter only removes coarse particles, its function is to help protect the rear filter elements from being clogged by these coarse particles.
Step 2: Filter element (OCB-GAC): The water passing through this filter will remove chlorine, excess organic matter and odorous gases from the water. In the case of limestone water in your home, this No. 2 filter core will be replaced by the Cation core.
Step 3: 1-micron PP filter helps to remove suspended particles larger than 1 micron in water. And if step 2, you have used a limestone filter core, this core number 3 will be replaced with Carbon Blook core helps remove organic and suspended substances.
Read more: How to filter lead from domestic water
Step 4: RO filter with TFC (Thin Film Composite) has 0.0001 micrometers, which is like the heart of RO water purifier to help eliminate 99.99% of viruses, bacteria, amoebas, arsenic, heavy metal ions and microscopic impurities are invisible to the naked eye. All will be removed by this RO membrane, helping the water become pure.
Step 5: T33-GAC core is made of activated carbon, which helps eliminate the horizontal taste of the water.
Step 6: Nano Silver is installed in the final position of the RO water purifier system to prevent re-contamination when water flows through the joints in the filtration system, besides contributing to neutralizing acid. , pH balance makes water taste more delicious.
Principle of the whole house RO water purifier installation
Step 7: Supplementing minerals beneficial to the body thanks to the Rock Mineral core, helping to make the water both sweet and essential minerals.
So the water through these 7 steps will become pure, standard directly drinking water without boiling.
Diagram of the RO water filter cartridges operation
So, if you have understood the principle of RO water purifier, then we will describe how to install a RO water purifier for direct drinking!
Whole House Water Purifier Installation With Detailed Diagram
Instructions on how to install the whole house RO water purifier
To be able to use a guaranteed water source in addition to owning a genuine water filter, you also need to know how to install a home water filter and replace the core periodically according to the manufacturers recommendations in order to get standard water.
Below is a diagram of how to install a household water filter that you can refer to for application.
16 steps to instal water filter
To ensure the smooth operation of the water purifier and avoid problems during use, it is necessary to follow the installation of a home water purifier following the following basic steps:
Step 1: Divide the inlet water at the sink or water-outlet positions, locking the inlet water when it is not yet installed in the machine.
Step 2: Peel the plastic at cores 1,2,3 into the corresponding filter cup. Then tighten filter cups No. 2 and No. 3, cup No. 1 moderate to loosen.
Step 3: Connect the big RO wire to the input end of the cup No. 1. When installing the water filter, make sure the screw must be wrapped and melt all threads to maximize the force of the connection between the RO wire and the screw.
Step 4: At the output end of cup 3, remove the RO wire connected from this output position to the input of the RO membrane, then take the small RO wire segment (outer section) connected directly from the digital cup outlet. 3 to the water discharge location to prepare the core wash process No. 1,2,3.
Step 5: Plug the power plug of the RO into the power source, and open the water valve of the stainless steel plug to start rinsing the preservatives of the core number 1,2,3. This process takes 20 minutes.
Step 6: During the rinsing process, the water from the No. 1 cup overflows, then tighten the cup No. 1. Note that when screwing the filter cup, do not screw it too tight, loosen 1-2 threads. Or else it will lead to the phenomenon that the machine works but cannot filter the water.
Step 7: After about 20 minutes, proceed to rinse the core number 1,2,3, we unplug the power plug, and reconnect the RO wire from the input of the RO membrane shell to the input of the filter cup No. 3 (as an initial state)
Step 8: Wear gloves and peel off plastic bags outside of the RO membrane. Steps 8, 9, 10, who install the water purifier should threaten gloves to ensure safety and hygiene and do not bring more dirt on the layer.
Step 9: Absorb RO membrane with pure water; you can use bottled pure water to absorb water evenly, the structure of the RO membrane expands steadily to ensure maximum filtration performance.
Step 10: Insert and firmly press the RO membrane inside the membrane shell, the top with the black washer inward.
Step 11: Close and tighten the RO membrane cover. Use pliers to twist the stopper to avoid water leakage.
Step 12: Connect the RO wires small wire from the waiting position of the Flow valve, follow the drain line of the family.
Step 13: Clean the RO membrane. At the output end of the RO membrane (the quail connected to the green card), disassemble the green wire, then connect the small RO wire segment (outside cable) to the family’s water discharge.
Step 14: Plugin power to start the washing process, preserving process in about 20 minutes.
Step 15: After RO membrane cleaning is complete, re-plug the wire according to the original installation of the RO membrane cover. And connect the pure water output wire of the housing to the pressure vessel.
Step 16: From the pressure tank, connect to the inlet of the filter element 5. The cores 5 and 6 are already connected.
So after 16 steps of installing the above water filter, you have completed the process of installing the water filter. To ensure the correct and correct installation, you can leave information for advice on installation or use home installation services, with professional and fast installation and warranty service. Reasonable will help you get a safe source of water, meet direct drinking water standards.
To prolong the duration of water purifiers after installing water purifier by above instructions, you also need to pay attention to the best storage. The thing to remember here is that you need to regularly clean the dirt, grease attached to cause loss of aesthetics and affect the filtration system.
For families with space, you can buy an extra cabinet because thanks to the outer enclosure, the product will not be contaminated with dirt, grease, insects, or bites from mice and power lines and water lines. In addition to protecting the water filter when stored in the cabinet, it also acts as an interior decoration for your home space more luxurious.
Above are the principles of the whole house water purifier installation that you can follow. Hopefully, that information, along with the detailed diagram would help you install the water filter easily at home.